DTSL,DTXL,DTSF,DTXF
wire tension counter is suitable for thin optical fibers and tubular cords
Hand-held wire tension meters For tubular wire and monofilament glass fiber
Features
DTS/X L：
4 Tension ranges availablefrom 150 - 2500 cN up to 2 - 20 daN
Electronic tension meter for cables, ropes, wires, buffer tubes, fibre strands etc. up to 10 mm Ø, as well as flat material up to 10 mm width.
DTS/X F：
4 Tension ranges availablefrom 1.0- 2.00 cN up to 20 - 1000 cN
Applications for fragile filaments with Ø up to max. 1.5 mm.
Tension meter with many functions as turnable display, thickness compensation and possibility of custom made calibrations
Special Features
DTSL/DTXL
Ball-bearing mounted guide rollers 29.5 mm groove Ø
– V-grooved (for material with max. 5 mm Ø)
– U-grooved (for material with 3 up to 5 mm Ø)
– tape grooved (for material with max. width of 10 m
DTX L/F：
Memory for 60.000 readings
USB interface
Tension meter DTXL with 5 different memory modes:
Mode S: statistics only
Mode H: storage of the X-Y-diagram for reviewing after finishing a series of measurement (e.g. short time spooling)
Mode C: continuous logging over a user set time and different series of measurement (2 Hz)
Mode F: fast, continuous logging over a user set time and different series of measurement (1000 Hz)
Mode D: storage of single readings and statistic
10 Material memory locations for customer made calibrations
Software Tension Inspect 3 for displaying real-time readings on a PC and to store them into a file
Wi-Fi module for wireless communication with a PC (optional)
DT S/X F: Large, v-grooved guide rollers with 32 groove diameter, ball bearing mounted
Large bending radius assures gentle handling of the material being measured
Special guides on the bracket assembly permit easy material acquisition
Calibration with Polyamide Monofilament (PA)
Tension meter with large, backlight LCD-display
3 different display modes:
– numeric
– numeric with bargraph
– numeric with graph (Time-Tension)
The display rotates in 90° steps for better reading
New, unique, force reduced material catching system
Automatic „Zero-Setting“ in each measuring position using a special sensor technique
4 Material memory locations for customer made calibrations
Calibration adjustment for fine tuning of the calibration if material differs from the used calibration material
Programmable MIN- and MAX alarms: indication in the display, if reading is out of limits
High speed data sampling (internal 8 kHz) and recording of MIN-, MAX-, last reading, PEAKS, average and standard deviation
Selectable units of measurement: cN, daN, g, kg, N, lb
Menu set-up in English or German language
Flexible menu set-up to meet operators demand
Some functions can be password protected
Note: Tension meter DTXF offers additional features, like interface, statistical evaluation on PC and a large internal memory.
Standard Features
Everything in operator's view:
– the guide rollers
– the measured material
– the readings
Filament guide and roller shifting mechanism ensure easy acquisition of the running material
Rubberized handle provides a secure hold in the operators' hand
Tension meter with rugged aluminium housing
LiPo accumulator (approx. 40 hours continuous operation) with AC adapter
CE certified, interference resistant against static electrifications
Certificate of Compliance with the order 2.1 according EN 10204 is included
Optionally available: Inspection Certificate 3.1 according EN 10204 with calibration report
4 Tension ranges availablefrom 150 - 2500 cN up to 2 - 20 daN
Electronic tension meter for cables, ropes, wires, buffer tubes, fibre strands etc. up to 10 mm Ø, as well as flat material up to 10 mm width.
DTS/X F：
4 Tension ranges availablefrom 1.0- 2.00 cN up to 20 - 1000 cN
Applications for fragile filaments with Ø up to max. 1.5 mm.
Tension meter with many functions as turnable display, thickness compensation and possibility of custom made calibrations
Special Features
DTSL/DTXL
Ball-bearing mounted guide rollers 29.5 mm groove Ø
– V-grooved (for material with max. 5 mm Ø)
– U-grooved (for material with 3 up to 5 mm Ø)
– tape grooved (for material with max. width of 10 m
DTX L/F：
Memory for 60.000 readings
USB interface
Tension meter DTXL with 5 different memory modes:
Mode S: statistics only
Mode H: storage of the X-Y-diagram for reviewing after finishing a series of measurement (e.g. short time spooling)
Mode C: continuous logging over a user set time and different series of measurement (2 Hz)
Mode F: fast, continuous logging over a user set time and different series of measurement (1000 Hz)
Mode D: storage of single readings and statistic
10 Material memory locations for customer made calibrations
Software Tension Inspect 3 for displaying real-time readings on a PC and to store them into a file
Wi-Fi module for wireless communication with a PC (optional)
DT S/X F: Large, v-grooved guide rollers with 32 groove diameter, ball bearing mounted
Large bending radius assures gentle handling of the material being measured
Special guides on the bracket assembly permit easy material acquisition
Calibration with Polyamide Monofilament (PA)
Tension meter with large, backlight LCD-display
3 different display modes:
– numeric
– numeric with bargraph
– numeric with graph (Time-Tension)
The display rotates in 90° steps for better reading
New, unique, force reduced material catching system
Automatic „Zero-Setting“ in each measuring position using a special sensor technique
4 Material memory locations for customer made calibrations
Calibration adjustment for fine tuning of the calibration if material differs from the used calibration material
Programmable MIN- and MAX alarms: indication in the display, if reading is out of limits
High speed data sampling (internal 8 kHz) and recording of MIN-, MAX-, last reading, PEAKS, average and standard deviation
Selectable units of measurement: cN, daN, g, kg, N, lb
Menu set-up in English or German language
Flexible menu set-up to meet operators demand
Some functions can be password protected
Note: Tension meter DTXF offers additional features, like interface, statistical evaluation on PC and a large internal memory.
Standard Features
Everything in operator's view:
– the guide rollers
– the measured material
– the readings
Filament guide and roller shifting mechanism ensure easy acquisition of the running material
Rubberized handle provides a secure hold in the operators' hand
Tension meter with rugged aluminium housing
LiPo accumulator (approx. 40 hours continuous operation) with AC adapter
CE certified, interference resistant against static electrifications
Certificate of Compliance with the order 2.1 according EN 10204 is included
Optionally available: Inspection Certificate 3.1 according EN 10204 with calibration report
Specification
DTSL/DTXL Available Models
DTSF/DTXF Available Models
* Outer distance between outside guide rollers
** Suitable for 95 % of applications
| Model | Measuring Range | Resolution | Measuring Head Width* | SCHMIDT Calibration Material | |
| DTSL-2500 | DTXL-2500 | 150 – 2500 cN | 1 cN | 185 mm | With convenient material for each roller design |
| DTSL-5000 | DTXL-5000 | 250 – 5000 cN | 1 cN | 185 mm | With convenient material for each roller design |
| DTSL-10K | DTXL-10K | 1.00 – 10.00 daN | 0.01 daN | 235 mm | With convenient material for each roller design |
| DTSL-20K | DTXL-20K | 2.00 – 20.00 daN | 0.01 daN | 235 mm | With convenient material for each roller design |
DTSF/DTXF Available Models
| Model | Measuring Range | Resolution | Measuring Head Width* | SCHMIDT Calibration Material PA** | |
| DTSF-200 | DTXF-200 | 1.0 – 200.0 cN | 0.1 cN | 140 mm | PA: Ø0.12mm |
| DTSF-500 | DTXF-500 | 1.0 – 500.0 cN | 0.1 cN | 140 mm | PA: Ø0.20mm |
| DTSF-1000 | DTXF-1000 | 10 – 1000 cN | 1 cN | 140 mm | PA: Ø0.30mm |
| DTSF-2000 | DTXF-2000 | 20 – 2000 cN | 1 cN | 140 mm | PA: Ø0.50mm |
* Outer distance between outside guide rollers
** Suitable for 95 % of applications
